Symptoms Of Cancer

Identify the separate wooden components and lay them out in order of assembly. Stick a short strip of masking tape on the front face of every component. Write the part identification letter on the masking tape with a marker pen.

Place each screw or bolt on leading in the included full-sized parts diagram Choose Comfortable baby bedding to identify them by letter reference and size.

Insert the tubular connector nuts "I" in to the relevant holes on the top and bottom with the long slatted side "R" from the crib. Thread Allen head bolts marked "F" by way of the legs marked "N" for the left side Visit Site and "O" for the right side; ensure that the bottom taper and extended slot faces inward. Position the legs on the ends with the long slatted "R" side, and thread the connecting bolts in to the tubular nuts using the Allen wrench provided. Don't tighten at this stage.

Place the lengthy foot cap marked "V" on prime of the slatted stationary side "R." Insert four Allen head bolts "G" up through the holes in the leading rail in the slatted side "R." Thread the bolts into the factory fitted threaded insert and tighten securely together with the Allen wrench. Tighten the Allen head bolts "F" connecting the leg posts for the slatted side.

Insert the Allen head bolts "F" via the holes within the foot posts "P" and "Q." Insert the tubular connector nuts "I" up via their respective holes inside the second extended slatted side "S." Position the posts "P" and "Q" against the finish with the second slatted side "S," together with the tapered ends pointing downward. Thread the Allen head bolts into the tubular nuts. Don't tighten yet.

Push 4 Allen head bolts "F" up by way of their respective holes inside the top rail from the second slatted side "S." Position the foot cap "V" on top with the slatted side. Thread the Allen head bolts "F" into the factory-fitted threaded inserts and tighten securely with the Allen wrench. Tighten the Allen head bolts "P" connecting the leg posts to the slatted side.

Identify the headboard and footboard slatted end pieces marked "M"; these are identical, but the part with product stickers attached is used as the footboard. Position the foot caps "L" on prime of every slatted finish piece with all the radius finish facing the front of the crib. Insert the 4 Allen head bolts "G" up through the leading rail. Thread the bolts in to the factory-fitted threaded inserts and tighten securely with all the Allen wrench.

Insert Allen head bolts "D" into the rear foot posts in the two slatted end pieces "M." Thread the bolts in to the matching factory fitted threaded inserts on the finish foot posts "N" and "O," fitted to the extended slatted side "R." Repeat by bolting the opposite sides of the slatted end pieces "M" to their respective matching factory-fitted threaded inserts on the legs "P" and "Q" attached for the slatted side piece "S." Tighten all Allen head bolts securely using the Allen wrench to complete the free-standing frame with the crib.

Determine the height at which you wish to install the spring base for the inside with the crib. Set the upward pointing swiveling swing arms on the ends of the spring base at a slight outward angle.

Lift the spring base into the crib together with the help of a friend. Adjust the angle of the swing arms if necessary to align the attaching holes within the swing arms up with the bolt holes on the end slats of crib ends "M," at your pre-selected height. Insert the short Allen head bolts "C" via the holes inside the swing arms and thread them in to the factory fitted threaded inserts on the finish slats with the crib ends "M." Tighten securely with all the Allen wrench. Fill the empty holes in the crib ends "M" together with the bronze inserts "H" provided inside the kitChild Craft Baby Bed Instructions.

Check-tighten all Allen head screws on the crib with all the Allen wrench. Location your selected mattress inside the crib.

Convert the crib into an open-sided toddler bed by initial removing the mattress. Undo the bolts holding the foot cap "V" for the best of the slatted side piece marked "S" and remove the foot cap. Remove the Allen head bolts "F" attaching the front slatted side marked "S" for the foot posts marked "P" and "Q." Store the slatted side "S" in case you need to convert the bed back into a crib at a later stage. Remove the spring base swing arm bolts marked "C" and lift the spring base out with the crib.

Stretch the foot posts "P" and "Q" apart just enough to allow the wood dowels within the ends in the crib stretcher post marked "T" to fit into the holes drilled into lower part of the foot posts "P" and "QChild Craft Baby Bed Instructions." Install the crib stretcher by fitting the dowels into their respective holes and re-inserting the two lower Allen head bolts "F" by means of the lower holes in end posts "P" and "Q." Tighten securely with all the Allen wrench.

Re-install the spring base within the lowest possible position. Remove the lowest bronze insert nuts "H" and bolt the swing arms back onto the crib ends marked "M" inside the lowest holes. Tighten securely with all the Allen wrench.

Attach the left foot post cap marked "W" as well as the perfect foot post cap marked "X" for the top with the foot posts marked "P" and "Q" by inserting Allen head bolt "E" by way of their locator holes and into the factory-fitted threaded inserts on the tops of foot posts "P" and "Q." Tighten securely together with the Allen wrench.